What's new
By:
USCHO Fan Forum

This is a sample guest message. Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!

  • The USCHO Fan Forum has migrated to a new plaform, xenForo. Most of the function of the forum should work in familiar ways. Please note that you can switch between light and dark modes by clicking on the gear icon in the upper right of the main menu bar. We are hoping that this new platform will prove to be faster and more reliable. Please feel free to explore its features.

The Home Improvement Thread. Successes and Failures

Status
Not open for further replies.
I had to disassemble the entire front panel of the dishwasher twice because my lovely and beautiful wife was distracted by a squirrel on the deck and fell on top of the door.

Mind you, this was also a nice bosch with about 2-3 weeks of use after waiting like four months for it. First door inner panel replacement we got had a bad corner so it wasn't going to seal. Finally got the replacement a month and a half later. Ended up slicing my finger really bad getting the soap dispenser out.

Anyways, good luck with the clean out. :)


Maybe check the drain hose and disposal to see if much of it got stuck there. Easy to fix that.

Otherwise you could always just run the boiling hot water through the drains several times in in a row. I usually do a boiling hot water flush several times a year just to flush out any built up junk. I also drain and flush the water heater annually.

Last time I had a root in the drain, the guy asked me how old the house was. I told him early 90s and he asked if I had the pipes replaced recently. Said they were extremely clean. *shrug*
 
Anyone have experience drilling into a hollow core door? I'm trying to hang a mirror, and I have the correct hollow door anchor, but the drill isn't going at all. I mean, I could push harder, but I was pushing pretty hard and it still wouldn't go in more than a couple of millimeters, so that says to me I'm not doing something right. I know hollow core isn't as much wood as compressed cardboard and other materials, so I'm wondering if I need a special drill bit?
 
French Rage said:
Anyone have experience drilling into a hollow core door? I'm trying to hang a mirror, and I have the correct hollow door anchor, but the drill isn't going at all. I mean, I could push harder, but I was pushing pretty hard and it still wouldn't go in more than a couple of millimeters, so that says to me I'm not doing something right. I know hollow core isn't as much wood as compressed cardboard and other materials, so I'm wondering if I need a special drill bit?
Click to expand...

Start with a really small bit, like a 1/16, to get a pilot hole started. The move put a size or two. Rinse and repeat as needed.
 
Sounds like bit isn't sharp, get a new bit. It should drill like any other piece of wood and if that bit won't start peeling out wood its really dull
 
French Rage said:
Anyone have experience drilling into a hollow core door? I'm trying to hang a mirror, and I have the correct hollow door anchor, but the drill isn't going at all. I mean, I could push harder, but I was pushing pretty hard and it still wouldn't go in more than a couple of millimeters, so that says to me I'm not doing something right. I know hollow core isn't as much wood as compressed cardboard and other materials, so I'm wondering if I need a special drill bit?
Click to expand...

Just about any bit will get through a hollow core door skin. This may seem a silly question, but is your drill on reverse, or are you using a masonry bit meant for a hammer drill?
 
St Clown with the win, though I appreciate all suggestions. Worked my way from 1/16 to 3/16 to 5/16 and then the latter finally worked!
 
I replaced one of the light switches in the living room with a Lutron dimmer. Supposed to be the Cadillac of dimmers. And it appears to be. Works great, no buzz, no flicker. Problem is, the three way switch next to it no longer lines up with it. The Lutron sits slightly higher. They're off by a small enough amount that I can jam the cover on, but then it's not even. I figure my best bet to get a switch that lines up is to get another Lutron toggle that is non-dimmable, but for the life of me I cannot find one. After some searching I'm not even sure they make one.

At this point I feel like my only options are to live with the uneven wall plate or start a trial-and-error of different brands of switches.
 
You just have to standardize on the brand. When we do replacements, every switch in the room gets replaced and completely rewired.
 
Spartanforlife4 said:
I replaced one of the light switches in the living room with a Lutron dimmer. Supposed to be the Cadillac of dimmers. And it appears to be. Works great, no buzz, no flicker. Problem is, the three way switch next to it no longer lines up with it. The Lutron sits slightly higher. They're off by a small enough amount that I can jam the cover on, but then it's not even. I figure my best bet to get a switch that lines up is to get another Lutron toggle that is non-dimmable, but for the life of me I cannot find one. After some searching I'm not even sure they make one.

At this point I feel like my only options are to live with the uneven wall plate or start a trial-and-error of different brands of switches.
Click to expand...

I assume its a small amount in difference? Shim the switch that sits in from the Lutron. Small washers between J box and switch to move switch out. You might get with just loosening screws to allow switch to move out when you tighten cover plate screws.
 
walrus said:
I assume its a small amount in difference? Shim the switch that sits in from the Lutron. Small washers between J box and switch to move switch out. You might get with just loosening screws to allow switch to move out when you tighten cover plate screws.
Click to expand...

It’s not much, I’ll have to measure when I get home for an exact difference. The Lutron sits slightly higher. Small enough to make it look like there’s wiggle room to make it work, but large enough that none of my adjustments have worked so far. Maybe I just have to tinker a little more.
 
JFC, did I ever get fleeced by the former owner of my house and his sh*tty DIY work. We've got a walk-in shower in our main bathroom and, to be fair, we'd been neglecting to clean out our shower drain for a few months. It flooded about 90 minutes ago while my wife was attempting to shower and some of it spilled over the edge of the shower pan. I ran into the basement for a plunger and saw there was water dripping all over one area and soaking through a bunch of boxes we had stored down there, because the fucker apparently didn't seal things properly when he redid that bathroom in 2018. Grrrrrrrrrrrreat. An hour of screaming later, we've dried up most of the water but now we have to unpack all the wet boxes. We're supposed to be hosting Thanksgiving in two days, the house is a mess, I don't have time for this sh*t.
 
Oh shit, that blows man... I'm sorry.

I'll use this as a reminder I should run my drains again soon. BTW, it's amazing what a good amount of baking soda and a cup of vinegar will do for a drain.
 
FadeToBlack&Gold said:
A couple weeks back, my wife finally got ahold of the Code Enforcement Officer while I was working. She got rather Karenish about the officer's cryptic letter citing some bull**** bylaw about replacing damaged property that we couldn't even find in the online code book.
Click to expand...

Postscript - we know someone on the City Council, and after he recently heard our story he asked us for a copy of the officer's letter. Apparently they're planning to sit down with her and review her performance. I guess she's been sending other unclear/cryptic letters on official city letterhead and there have been several complaints. We have a lot of older residents who have been here a long time, including the officer, and I suspect that she may be friends with many of them and possibly making up threatening letters as a favor to her buddies. In which case, I'd expect her to be terminated at a minimum.
 
FadeToBlack&Gold said:
Postscript - we know someone on the City Council, and after he recently heard our story he asked us for a copy of the officer's letter. Apparently they're planning to sit down with her and review her performance. I guess she's been sending other unclear/cryptic letters on official city letterhead and there have been several complaints. We have a lot of older residents who have been here a long time, including the officer, and I suspect that she may be friends with many of them and possibly making up threatening letters as a favor to her buddies. In which case, I'd expect her to be terminated at a minimum.
Click to expand...

That's not a postscript, that's Chapter 2. Now I'm curious where this goes :-D
 
Is there a company or type of professional who will come to your house and take a top to bottom look at everything and give you a 'honey do' list of recommended essential and/or cosmetic improvements? We live in a 1960s house and stuff is really starting to come up for repair, but I don't know the order of importance and need someone who can look at stuff and say 'Hey, that's a problem now' or 'That's going to be a problem soon' etc. So far i only found the template of hvac contract https://lawrina.com/templates/hvac-contract/ and we are going to sing it in the next couple of days.
 
Last edited:
Status
Not open for further replies.
Back
Top